Show Me Tell Me...
What happens on the driving test day.
Before you start the practical driving test. The Driving test Examiner will ask if you would like your Driving Instructor to accompany you in the car on the driving test, you will have an eyesight test, you will be asked to read a number plate from approximately 20 meters and be asked 1 show me and 1 tell me question as part of the vehicle safety questions.
1. About the questions
You’ll be asked 2 vehicle safety questions. These are also known as the ‘show me, tell me’ questions.
The examiner will ask you one ‘show me’ question, where you’ll have to show them how you’d carry out a vehicle safety check.
You’ll also be asked one ‘tell me’ question, where you’ll have to explain to the examiner how you’d carry out the check.
2. ‘Show me’ questions
Show me how you would check that the direction indicators are working.
Applying the indicators or hazard warning switch and check functioning of all indicators. (may need to switch ignition on, prompt not to start engine).
Show me how you would check the brake lights are working on this car,
(if you need to switch the ignition on, please don’t start the engine).
Operate brake pedal, make use of reflections in windows, garage doors, etc, or ask someone to help, (may need to switch ignition on, prompt not to start engine).
Show me, or explain how you would check that the power assisted steering is working before starting a journey.
If the steering becomes heavy the system may not be working properly. Before starting a journey two simple checks can be made.
Gentle pressure on the steering wheel, maintained while the engine is started, should result in a slight but noticeable movement as the system begins to operate. Alternatively turning the steering wheel just after moving off will give an immediate indication that the power assistance is functioning.
Show me how you would check the parking brake (handbrake) for excessive wear;
(make sure you keep safe control of the vehicle).
Apply footbrake firmly. Demonstrate by applying parking brake (handbrake) so that when it is fully applied it secures itself,
and is not at the end of the working travel.
Show me how you would check that the horn is working.
Check is carried out by using control (turn on ignition if necessary).
Show me how you would clean the windscreen using the windscreen washer and wipers.
Operate control to wash and wipe windscreen (turn ignition on if necessary).
Show me how you would switch on the rear fog light(s) and explain when you would use it/them, (no need to exit vehicle).
Operate switch (turn on dipped headlights and ignition if necessary). Check warning light is on. Explain use.
Show me how you switch your headlight from dipped to main beam and explain how you would know the main beam is on.
Operate switch (with ignition or engine on if necessary), check with main beam warning light.
Show me how you would set the demister controls to clear all the windows effectively.
Set all relevant controls including fan, temperature air direction / source and heated screen to clear windscreen and windows.
Engine does not have to be started for this demonstration.
Open the bonnet, identify where you would check the engine oil level
and tell me how you would check that the engine has sufficient oil.
Identify dipstick / oil level indicator, describe check of oil level against the minimum / maximum markers.
Open the bonnet, identify where you would check the engine coolant level
and tell me how you would check that the engine has the correct level.
Identify high/low level markings on header tank where fitted or radiator filler cap, and describe how to top up to correct level.
Open the bonnet, identify where the brake fluid reservoir is
and tell me how you would check that you have a safe level of hydraulic brake fluid.
Identify reservoir, check level against high/low markings.
3. ‘Tell me’ questions
Tell me how you would check that the brakes are working before starting a journey.
Brakes should not feel spongy or slack. Brakes should be tested as you set off. Vehicle should not pull to one side.
Identify where the windscreen washer reservoir is and tell me how you would check the windscreen washer level.
Identify reservoir and explain how to check level.
Tell me where you would find the information for the recommended tyre pressures for this car
and how tyre pressures should be checked.
Manufacturer’s guide, use a reliable pressure gauge, check and adjust pressures when tyres are cold, don’t forget spare tyre, remember to refit valve caps.
Tell me how you make sure your head restraint is correctly adjusted so it provides the best protection in the event of a crash.
The head restraint should be adjusted so the rigid part of the head restraint is at least as high as the eye or top of the ears, and as close to the back of the head as is comfortable. Note: Some restraints might not be adjustable.
Tell me how you would check the tyres to ensure that they have sufficient tread depth
and that their general condition is safe to use on the road.
No cuts and bulges, 1.6mm of tread depth across the central 3/4 of the breadth of the tyre and around the entire outer circumference.
Tell me how you would check that the headlights and tail lights are working (no need to exit vehicle).
Operate switch (turn on ignition if necessary), then walk round vehicle. As this is a ‘tell me’ question, there is no need to physically check the lights.
Tell me how you would know if there was a problem with your anti lock braking system. (ABS)
Warning light should illuminate and will remain on, if there is a fault with the anti lock braking system.
Need a Quick driving test?